CNC Router - Revision history

Ave at 22:24, 16 July 2023

2023-07-16T22:24:29Z

← Older revision		Revision as of 22:24, 16 July 2023
Line 3:		Line 3:
	[[https://docs.google.com/document/d/1OM1HOfPP3oHocmwyrcVcchgL6jWcF3K5Lw0Kzu6ZqcM/edit?usp=sharing \| Class reference material]]		[[https://docs.google.com/document/d/1OM1HOfPP3oHocmwyrcVcchgL6jWcF3K5Lw0Kzu6ZqcM/edit?usp=sharing \| Class reference material]]
	== Smaller router ==		== Smaller router ==
	This machine runs [[http://wiki.fluidnc.com/ \| FluidNC]]. Here is the power switch for the controller at the time of writing		This machine runs [[http://wiki.fluidnc.com/ \| FluidNC]]. Reading this document does not clear you to run the machine. Please schedule a training on the Discord. Here is the power switch for the controller at the time of writing
	[[File:Cncsw2.jpeg\|thumb\|center\|upright=1.0]]		[[File:Cncsw2.jpeg\|thumb\|center\|upright=1.0]]
	[[File:Cnc3.PNG\|thumb\|center\|upright=3.0\|This is the web interface you get when connecting directly to it's wifi hotspot. At the time of writing, it's pretty unreliable and will hopefully be updated soon]]		[[File:Cnc3.PNG\|thumb\|center\|upright=3.0\|This is the web interface you get when connecting directly to it's wifi hotspot. At the time of writing, it's pretty unreliable and will hopefully be updated soon]]

Ave at 22:20, 16 July 2023

2023-07-16T22:20:53Z

← Older revision		Revision as of 22:20, 16 July 2023
Line 1:		Line 1:
	We have a 4' x 4' CNC router running LinuxCNC(EMC2)		We have 2 big CNC routers. You need to schedule a class to get trained and signed off on them.
			== 4' x 4' CNC router running LinuxCNC(EMC2) ==
			[[https://docs.google.com/document/d/1OM1HOfPP3oHocmwyrcVcchgL6jWcF3K5Lw0Kzu6ZqcM/edit?usp=sharing \| Class reference material]]
			== Smaller router ==
			This machine runs [[http://wiki.fluidnc.com/ \| FluidNC]]. Here is the power switch for the controller at the time of writing
			[[File:Cncsw2.jpeg\|thumb\|center\|upright=1.0]]
			[[File:Cnc3.PNG\|thumb\|center\|upright=3.0\|This is the web interface you get when connecting directly to it's wifi hotspot. At the time of writing, it's pretty unreliable and will hopefully be updated soon]]
			It's recommended you use [[https://software.openbuilds.com/#openbuilds-control \| Openbuilds CONTROL]]. To connect, you can use a micro-usb and plug into COM directly, OR connect to the FluidNC hotspot with password 12345678. In Openbuilds CONTROL, click Scan Network
			[[File:Cnc1.PNG\|thumb\|center\|upright=3.0\|]]
			Make sure the IP range looks like this with 192.168.0.1-254
			[[File:Cnc1-2.PNG\|thumb\|center\|upright=3.0]]
			Then the device should show up in the list. Click connect.
			[[File:Cnc1-3.PNG\|thumb\|center\|upright=3.0\|]]
			The first thing you probably have to do is clear the alarm that's on at startup
			[[File:Cnc2-0.PNG\|thumb\|center\|upright=3.0\|]]
			At the time of writing, CONTROL automatically disables homing due to a bug. There's probably a configuration change that could fix this. You can manually home with $H or $HZ if you only want to home the Z axis for example
			[[File:Cnc2.PNG\|thumb\|center\|upright=2.0\|]]
			Jog and touch off as you normally would. Once you're ready to run the machine, make sure the coolant is flowing and not leaking
			[[File:Cncsw1.jpeg\|thumb\|center\|upright=1.0\|Power switch]]
			To use the spindle, turn the power switch on, hold the green button for a couple seconds, and adjust the knob to set your RPMs. At 400hz, the spindle spins at 24,000rpm, so if you wanted 18,000rpm, you would set the knob to 300hz. 300hz is a good number for most things. The controller is has a module for connecting to the spindle and setting its speed electronically, but that hasn't been set up at the time of writing.
			[[File:Cncsw3.jpeg\|thumb\|center\|upright=1.0]]
			While the machine is running, make sure the fan is spinning on the controller and that it's not been knocked out of place. Also make sure the cables and hose aren't catching on anything. If you're spraying coolant on your part, be careful not to get it on the wood in places where it's been milled flat or else they'll warp.

Eric: Created page with "We have a 4' x 4' CNC router running LinuxCNC(EMC2)"

2021-05-25T03:45:27Z

Created page with "We have a 4' x 4' CNC router running LinuxCNC(EMC2)"

New page

We have a 4' x 4' CNC router running LinuxCNC(EMC2)

← Older revision		Revision as of 22:24, 16 July 2023
Line 3:		Line 3:
	[[https://docs.google.com/document/d/1OM1HOfPP3oHocmwyrcVcchgL6jWcF3K5Lw0Kzu6ZqcM/edit?usp=sharing \| Class reference material]]		[[https://docs.google.com/document/d/1OM1HOfPP3oHocmwyrcVcchgL6jWcF3K5Lw0Kzu6ZqcM/edit?usp=sharing \| Class reference material]]
	== Smaller router ==		== Smaller router ==
	This machine runs [[http://wiki.fluidnc.com/ \| FluidNC]]. Here is the power switch for the controller at the time of writing		This machine runs [[http://wiki.fluidnc.com/ \| FluidNC]]. Reading this document does not clear you to run the machine. Please schedule a training on the Discord. Here is the power switch for the controller at the time of writing
	[[File:Cncsw2.jpeg\|thumb\|center\|upright=1.0]]		[[File:Cncsw2.jpeg\|thumb\|center\|upright=1.0]]
	[[File:Cnc3.PNG\|thumb\|center\|upright=3.0\|This is the web interface you get when connecting directly to it's wifi hotspot. At the time of writing, it's pretty unreliable and will hopefully be updated soon]]		[[File:Cnc3.PNG\|thumb\|center\|upright=3.0\|This is the web interface you get when connecting directly to it's wifi hotspot. At the time of writing, it's pretty unreliable and will hopefully be updated soon]]